description

1. Architectural and planning solutions

Trading center “AINA” is a four floor building with semi basement, located at Abylkhair-khana Avenue 42, Aktobe.

The architecture of trading center is distinct from Aktobe central square with its laconic manner, and distinct front elevation.

Building front elevations are made of glass in form of parallelepiped 96x36m. The ledge of the trading center is accomplished after Middle Asia style with stalactite work on 4 corners. It is Flex Building which allows using inner space freely.

Building dimensions – 84x36 m

Floor height – 4.8 m

Relative datum 0,000 is accepted level of 1st floor, which corresponds the absolute datum 219,100

Class of building by extent of responsibility – II

Factor of reliability – 0,95

Fire resistance rate of the building – III a

Architectural and planning solutions are determined by technological requirements of regulatory documents and architectural aesthetic appeal.

2. Construction solutions

Structural layout is carcass. Skeleton of the building is metallic with column grid 6x9m. Columns are box type from steel 40. B2 hammer braces are box type from steel [30, B] from wide-flange I-beam, belt and double angle iron 100*100*8. Metal objects are cleaned and embed by antirust primer GF-021 twice, and two times enamel type MC-132. Column inner armored by АS d-18 metal frame and firmed by M-200 type cement. Outer surface of metallic constructions is triple coated by fire-resistant paint “Akvest-911” for metallic constructions.

Columns foundation basis compiled from precast blocks on cast reinforced concrete SOST 13580-85 and precast concrete blocks GOST 13519-78.

Columns and metal beams are boxed-off by plaster slab. Basement walls are made of concrete blocks GOST 13519-78 insulated with expanded plastic and siding.

Floor structure is from factory-built concrete core unit PK 60-15 PK 60-12. Spandrels are precast concrete and metallic. Roof coating is roll type with side drain. Outward siding is from stained glass. As an external protection hinged stained-glass windows from aluminum profiles - series TP-50300 unified systems "TATPROF" (Tatarstan) are applied. Glass - a single-chamber double-glazed window of 24 mm and glass of 6 mm for platform. The aluminum skeleton fastens on all height over building perimeter every floor to metal carcass. Touching to glass details it is excluded. Double-glazed windows are glued SPO №С5ML-14-35М1 GOSMT 24866-99, covered DBL - 20, also are made by LLP «Saratov institute of glass» Saratov. Covering DBL - 20 provides light absorbing and energy saving (i.e. refracts solar beams and interferes with cold penetration from the outside and to heat outflow from within).

3. In-building services system

The building is connected to heat supply network of Joint Stock Company “Transenergo” and provided through 200mm heat network. At entrance semi-automatic inlet node is installed and divides into 3 autonomic heating systems. Every system can be adjusted individually, independently of whole complex. Every heating radiator is adjusted by its valves. Heating radiator is Italian manufacture from aluminum casting; pipes are metallic-plastic with diameter 20-50mm. Inside water supply and sewage collection system are connected to “Akbulak” Joint Stock Company network system.

4. Elevators

The Building is equipped with 4 passenger-elevators with carrying capacity of 630 kg manufactured by world’s best Finland company “KONE”, and 1 service elevator manufactured by Belorussian Mogilevskyi lift factory. Getting passenger lifts at the company with a world name, the comfort of system of safety of the standard "KOHE" is provided. Company "KONE" - as the world manufacturer wins first place among manufacturers of lifts. On the Mogilyov factory on manufacture of goods lifts it is technically equipped, modernization of goods lifts is estimated perfectly.

5. Ventilation and air-conditioning

Ventilation and air conditionings of a premise of a complex it is executed for climatic conditions of Aktobe and there comply with requirements SN P RK 4.02-05-2001 "Heating, ventilation and an air conditioning».

Air lines are executed from a sheet steel. Air lines of additional systems are accepted class P (dense), air lines of exhaust systems are accepted class N (normal), rectangular and round section.

Additional air moves organized directly in a premise. Removal of air from premises exhaust ventilation systems is carried out from zones in which it is most polluted or has most heat.

All air lines laid in limits of ventilation chambers, on a roof, on a ground floor of a building and air lines of systems K1-K8 are isolated foil-coated URSA with thickness of 50 mm. For the prevention of freezing of heaters of systems K1-K8 they can be blocked by their fan and the regulating valve, providing warming up of heaters, and then start-up of fans; at a stop the first disconnect fans, and then heaters. Air regulation is carried out by the regulating valve by change of the expense of the heat-carrier.

Productivity of the established forced-air and exhaust systems allows to make 4 multiple exchange of air within one hour depending on temperature.

Plan of the premise download